ITEM INCLUDES
DO35 V3Plus w/ Handbrake
Tow Pin 7/8" Shaft
Tow Pin Cover
Universal C-Spanner
Fitment Bolts
User Guide
The Adventure Continues with the DO35 V3Plus, taking you further than other couplings!
V3PLUS EXCLUSIVE FEATURES
Patented “Checklock” Gen.2 Dust Cap & Bumper for an easy, secure seal
Improved Bumper molding gives the from reflector strip improved staying power
Rear support webbing allows for mounting upside down on the underside of the drawbar
STANDARD V3 FEATURES
2 Stage ADR compliant locking mechanism
Low profile Bumper & Cap for impressive clearance
High articulation for improved handling off-road and on unmaintained roads
Available with or without handbrake
Suitable for use with most Weight Distribution System’s
Forged Yoke and Rear Nut for added strength
Exceeds ADR 62/01 and 62/02 strength requirements
One piece light weight Cast Housing
Standard Aus bolt pattern for easy fitment
7/8” shaft to fit most std. tow tongues
Improved towing safety
Combination of zn-ni and e-coat for superior corrosion protection
Greaseable Bushes for easy maintenance and noise free towing
No tow ball height restrictions
R.A.T Run Tested and Proven
ARTICULATION: 360 degrees axial, minimum 70 degrees other axes.
LOCKING: Fully ADR 62/02 compliant including automatic secondary lock
BOLT PATTERN: 4 bolts at 185mm x 54mm
RATING: 3.5 Tonne
ACTION: Drop-On
MAINTENANCE: Fully Greasable
For instructions on installation, maintenance and use refer the DO35 User Guide.
*Please note while the DO35’s Zn-Ni with E-Coat provides superior corrosion protection it may fade with extended exposure to UV. This does not affect the operation of the DO35. To best maintain the finish of the product, we recommend covering the DO35 coupling when not in use if stored outside and exposed to direct UV.
ITEM INCLUDES
DO45 Plus (No Handbrake)
Tow Pin 1 1/4" Shaft
Tow Pin Cover
Universal C-Spanner
Fitment Bolts
User Guide
Tame the Beast with the DO45 Plus!
PLUS SERIES EXCLUSIVE FEATURES
Patented “Checklock” Gen.2 Dust Cap & Bumper for an easy, secure seal
Improved Bumper now includes reflective reversing strip for easy alignment
Rear support webbing allows for mounting upside down on the underside of the drawbar
FEATURES
D-Value & V-Value ADR Compliant
2 Stage ADR compliant locking mechanism
Low profile Bumper & Cap for impressive clearance
High articulation for improved handling off-road and on unmaintained roads
Available with or without handbrake
Suitable for use with Weight Distribution System’s (where applicable)
Forged Yoke and Rear Nut for added strength
One piece light weight Cast Housing
Improved towing safety
Combination of zn-ni and e-coat for superior corrosion protection
Greaseable Bushes for easy maintenance and noise free towing
No tow ball height restrictions
R.A.T Run Tested and Proven
ARTICULATION: 360 degrees axial, minimum 70 degrees other axes.
LOCKING: Fully ADR 62/02 compliant including automatic secondary lock
BOLT PATTERN: 4 bolts at 185mm x 76mm (Front) x 54mm (Rear)
RATING: 4.5 TonneACTION:Drop-On
MAINTENANCE: Fully Greasable
For instructions on installation, maintenance and use refer the DO45Plus User Guide.
*Please note while the DO45Plus’s Zn-Ni with E-Coat provides superior corrosion protection it may fade with extended exposure to UV. This does not affect the operation of the DO45Plus. To best maintain the finish of the product, we recommend covering the DO45Plus coupling when not in use if stored outside and exposed to direct UV.
DO45 Version 1 & DO45Plus accessories and fittings are not interchangable
FREE SHIPPING AUS WIDE
* Please note product supplied and product shown may have minor cosmetic discrepancies
Usually ships within 2-3 business days
ALWAYS ON THE CUTTING EDGE.
Cutting edge performance starts with cutting edge LED technology. To achieve genuine category leading performance our Type-X™ Pro is equipped with 37 x Oslon High-Flux LEDs, selected for having the #1 highest lumen density per mm2 of any other comparable LED on the market. Compared to the two other leading spot lights brands similar offerings, the LEDs used in Type-X™ PRO have + 23% and +42% higher lumen density per mm2 in comparison. The net result is higher net light volume and unrivalled beam throw.
A WOLF IN WOLF’S CLOTHING
The hard-coated optical grade lens shares the same DNA as ballistic glass making it virtually indestructible. A UV stabiliser has also been added to ensure our lenses truly withstand the test of time with no discolouring or UV degradation. This has allowed us to do away with any secondary lens covers or filters which are known to significantly reduce light transmission.
ICONIC PERFORMANCE
Using the latest optic simulation modelling, the reflector geometry was tweaked over and over again to achieve a highly usable beam pattern. No doubt the attention grabber is the unrelenting beam distance of 1,155m (tested in pairs, combo beam), however the real strength of our Type-X™ PRO is in mid to long light distribution that really sets it apart.
Our key focus was on driver confidence, by increasing the beam throw the driver has longer analysis time. We maximised driver comfort by smoothing out the beam eliminating shadows. We reduced the light wasted in unimportant zones like treetops and immediately in front of the vehicle. The result is a homogeneous, unrelenting beam that that will support you well in any adventure. .
Unlike our competitors each Type-X™ PRO lamp has 6 built in flood reflectors for improved light distribution out into the road shoulders. The built in wide-beam reflector eliminates the need to add any wide beam covers, which are not only less efficient at distributing light, covers also withhold valuable light transmission.
- Product details and blurb care of STEDI
WHAT’S IN THE BOX
2 x STEDI Type-X PRO LED Driving Lights
2 x Protective STEDI Black Out Covers
2 x Grey Colour Rings
2 x Orange Coloured Rings
1 x Smart High Beam Wiring Harness DTP-2 Sealed Connectors, H4, HB3 adapter plugs to high beam. 60A Relay, Fuse, Switch
Complete Stainless Steel fastener kit.
Wiring & Fitting Instructions
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
OVERVIEW
The STEDI ST3K LED Light Bar was designed to bring a large amount of light to a small amount of space. With its small profile of just 63mm total height with the side brackets attached, you will find the ST3K is able to be mounted in locations like your front bar and grill whilst maintaining the factory look of your vehicle.
PERFORMANCE
The ST3K packs quite a powerful punch running off the same Pure Drive technology + LEDs as the popular Type-X and ST4K range. Ability to mount in tight spaces are its key trait as it can be mounted on your standard vehicle and prove to be a useful source of light whilst driving out bush with cars that don't have the space to run some of our larger LED light bars.
BEAM CHARACTERISTICS
Easily comparable to the STEDI Type-X and ST4K range the beam type of the ST3K follows in line. Providing a strong penetrating beam with 493m at 1 LUX and 55m out to the shoulders of the road with flood beam, the perfect all-rounder with low profile has arrived!
MARKET LEADING PERFORMANCE
ST3K-20L features 20 of OSRAM’s® finest OSLON® LED, selected for unrivalled efficiency.
4 Flood + 12 Spot + 4 Flood reflector distribution forms a remarkable beam that pushes the wide beam out at 50° and spot beam at 5.8° all the way to staggering 1 lux @ 493m
True White 5700K Colour temperature offers stunning clarity and definition.
Pure-Drive™ circuit design allow 97% of input power to go directly to LEDs.
BUILT TO WITHSTAND THE RELENTLESS PUNISHMENT OF THE DEEP AUSTRALIAN OUTBACK
Finished in 100% Polyester UV and abrasion resistant powder coat, ensures that Stedi bars will never discolour.
Pressure Equalization vent | Protects against water ingress, dust & contaminants.
IP68 | Dust & Particle tight + Water-proof up to 3 meters!
Environmentally sealed Deutsch ® DT-2 connector.
Protected against EMC and RFI.
Ultra-Low 51mm profile without the side brackets & 63mm with side brackets!
Includes Easy Fit High Beam Plug and Play Wiring Harness which includes H4 and HB3 Adapters making for an easy connection to high beam. Unlike the copycat harnesses on the market Stedi's has built in electronics making our harness compatible with even the most modern and sophisticated wiring systems
Backed by a Stedi 5 Year Replacement Warranty.
- Product details and blurb care of STEDI
WHAT’S IN THE BOX
ST3K 21.5inch LED LIGHT BAR
Stainless Fasteners
Stainless Steel Side Mounting Brackets
12v Quick Fit to High Beam Wiring, Relay, Wiring Kit and On/Off Switch
H4 and HB3 adapters included
Wiring Instructions
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
THE ULTIMATE LIGHT BAR
For almost a decade, the name STEDI has stood for cutting-edge design and market-leading performance. The ST3303-PRO is an aggregation of all things that have made us the globally distributed, coveted brand born right here in Australia.
A NEW REALM OF PERFORMANCE
Every good story starts with CREE LEDs. So, we commissioned CREE’s XPL HI emitter, which represents a +9% increase in lumen output at the same drive current over the already great (but now aging) CREE XM-L2 found in the previous model. 9% doesn’t sound like much, but the kicker is that the emitter die size drops down from 5 x 5mm to 3.5 x 3.5mm. Higher lumen density with tighter source improves the optic and emitter size relationship – We’ve effectively increased the optic diameter by 40% without physically increasing it. The result is huge light volume and tremendous beam throw.
NOW, ARE YOU SITTING DOWN?
Where others stop, we get started. The current draw is enormous, and quite literally unlike anything else on the market. The 60 LED variant draws 36 amp at 13.6v & @ 12.5v 40 amp. Have we got your attention yet? Now, you must, without any exception, we repeat, you must use the heavy-duty, dual relay (yes dual relay!), dual fused wiring harness we supply. The current is so intense, the 40 LED and 60 LED bars have two separate power cables (yes two separate power cables!) on either side of the light bar, and two separate breathers (yep two!) to deal with the enormous current draw.
BAR NONE.
Unquestionably, ST3303 PRO sits at the pinnacle of the STEDI offering. A pure expression of capability and design that converges with brutal performance, making the all-new ST3303 PRO unmistakably STEDI.
Provides flexible mounting options for your ScanGauge, allowing you to mount the ScanGauge on the Window or the Dash. Fully adjustable, the mount rotates 360 degrees and allows you to adjust the viewing angle for the best visibility.
Introducing the NARVA EX2 range of driving lights which has been designed with the DIY 4WD enthusiast in mind and is also ideal for a wide range of fleet and transport applications! With EXceptional beam pattern performance, EXtra-easy installation, EXceptional build quality and EXtensive customisation options to EXpress yourself.
Technical Information
INPUT VOLTAGE RANGE 9 – 33V
CURRENT DRAW @13.5V: 19.2A
LEDs 40 x 5 Watt Cree LEDs
LUMENS 27,200 raw / 19,400 effective
IP RATING IP68 & IP69K
COLOUR TEMPERATURE 5700°K
OTHER Beam type: Hybrid
Narva P/N: 72182
The EX2R range retains the output and build quality of the EX2 series with the addition of ADR/ECE approved front position lights offering visibility, and a distinctive appearance. These position lights are RGB enabled, allowing them to be changed to various colours when paired with the 12V RGB Bluetooth® Controller - a never before seen feature on the market (For off-road use only).
Technical Information
INPUT VOLTAGE RANGE 9-33V DC
CURRENT DRAW @13.5V/@28V: 7.2/3.5
LEDs 36
LUMENS Effective: 9780Lm
IP RATING IP68 & IP69K
OPERATING TEMPERATURE -40 - +60°
COLOUR TEMPERATURE 5700K ±5%
ECE R10
OTHER Raw lumens: 10800Lm
Narva P/N: 72843
ITEM INCLUDES
DO35 V3Plus (No Handbrake)
Tow Pin 7/8" Shaft
Tow Pin Cover
Universal C-Spanner
Fitment Bolts
User Guide
The Adventure Continues with the DO35 V3Plus, taking you further than other couplings!
V3PLUS EXCLUSIVE FEATURES
Patented “Checklock” Gen.2 Dust Cap & Bumper for an easy, secure seal
Improved Bumper molding gives the from reflector strip improved staying power
Rear support webbing allows for mounting upside down on the underside of the drawbar
STANDARD V3 FEATURES
2 Stage ADR compliant locking mechanism
Low profile Bumper & Cap for impressive clearance
High articulation for improved handling off-road and on unmaintained roads
Available with or without handbrake
Suitable for use with most Weight Distribution System’s
Forged Yoke and Rear Nut for added strength
Exceeds ADR 62/01 and 62/02 strength requirements
One piece light weight Cast Housing
Standard Aus bolt pattern for easy fitment
7/8” shaft to fit most std. tow tongues
Improved towing safety
Combination of zn-ni and e-coat for superior corrosion protection
Greaseable Bushes for easy maintenance and noise free towing
No tow ball height restrictions
R.A.T Run Tested and Proven
ARTICULATION:360 degrees axial, minimum 70 degrees other axes.LOCKING:Fully ADR 62/02 compliant including automatic secondary lockBOLT PATTERN:4 bolts at 185mm x 54mmRATING:3.5 TonneACTION:Drop-OnMAINTENANCE:Fully Greasable
For instructions on installation, maintenance and use refer the DO35 User Guide.
*Please note while the DO35’s Zn-Ni with E-Coat provides superior corrosion protection it may fade with extended exposure to UV. This does not affect the operation of the DO35. To best maintain the finish of the product, we recommend covering the DO35 coupling when not in use if stored outside and exposed to direct UV.
Ensure the safety of your camper or caravan when you're not there with Cruisemaster's own DO45 lock.
Gen.2 DO45Plus Lock.
The Cruisemaster™ DO45Plus Lock assembly consists of a dummy pin, two keys and lock chamber with dust cover.
How does it work? The dummy pin is to be inserted into the DO45Plus universal joint from the top end and the tip of the pin will protrude out at the bottom. The lock is then fitted to the protruding end of the pin and can be locked with a key. The coupling becomes inoperable which prevents others being able to hitch up to your trailer or van when your not there.
This product is covered by a 12 Month Mnaufacturers Warranty.
Warranty T&C's Apply.
IMPORTANT: Lock is suitable for use with DO45Plus Only
Not suitable for DO35 & DO45 V1 Only
Usually ships within 2-3 business days
18D-DO45PLUS-LOCK
LEGENDARY TYPE-X DNA
Three years since the inception of original Type-X, we’ve taken an already proven platform and completely redesigned it from the ground up. All-new reflector geometry, all-new LEDs and all-new housing. We’ve increased the depth of the optics by 35% allowing for a perfectly collimated beam and the resultant increase in light intensity. The beam diameter strikes a sublime balance between width and throw and will send light right out to 1,050m. Four dedicated built-in wide-beam optics disperse light in the nearfield, and transition beautifully with the spot beam.
STEDI DESIGN LANGUAGE
Some people call it the little things; for us, it is literally everything. We obsessed over even the most trivial geometries and design elements to achieve a visually stunning luminaire. The 4mm 304 Stainless steel bracket features our signature shoulder armor with laser-cut STEDI branding. A carefully considered orange rim surrounding the housing offers just the right amount of visual impact while ensuring that the overall look and feel plays nice equally on a Sandy Taupe Landcruiser as it will on Magnetic Grey Ranger.
ENTER THE WORLD OF STEDI
The internet is littered with mediocre lights. 98% of driving lights offered in the marketplace are off the shelf imports with the reseller’s laser logo and subsequent price mark-up. Don’t even get us started on the fictitious performance claims. When you enter the world of STEDI, you’re buying into a product which is mechanically and optically engineered with our know-how and our tooling, with our reputation and warranty standing right behind it. Our lights won’t fade, turn yellow and fall-off at the first sign of corrugations. Our photometric data is lab tested, not photoshopped – We stand by it.
- Product details and blurb care of STEDI
WHAT’S IN THE BOX
2 x STEDI Type-X SPORT LED Driving Lights
2 x Protective STEDI Black Out Covers
1 x Easy Fit High Beam Wiring with DTP-2 Sealed Connectors, H4, HB3 Adaptor plugs to high beam. 60A Relay, Fuse, Switch
3 Series Stainless Steel Nuts and Bolts
Rubber Shock Dampener
Wiring & Fitting Instructions
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
OVERVIEW
The STEDI ST3K LED Light Bar was designed to bring a large amount of light to a small amount of space. With its small profile of just 63mm total height with the side brackets attached, you will find the ST3K is able to be mounted in locations like your front bar and grill whilst maintaining the factory look of your vehicle.
PERFORMANCE
The ST3K packs quite a powerful punch running off the same Pure Drive technology + LEDs as our popular Type-X and ST4K range. Ability to mount in tight spaces are its key trait as it can be mounted on your standard vehicle and prove to be a useful source of light whilst driving out bush with cars that don't have the space to run some of our larger LED light bars.
BEAM CHARACTERISTICS
Easily comparable to the STEDI Type-X and ST4K range the beam type of the ST3K follows in line. Providing a strong penetrating beam with 348m at 1 LUX and 55m out to the shoulders of the road with flood beam, the perfect all-rounder with low profile has arrived!
MARKET LEADING PERFORMANCE
ST3K-10L features 10 of OSRAM’s® finest OSLON® LED, selected for unrivaled efficiency.
2 Flood + 6 Spot + 2 Flood reflector distribution forms a remarkable beam that pushes the wide beam out at 50° and spot beam at 5.8° all the way to staggering 1 lux @ 348m
True White 5700K Colour temperature offers stunning clarity and definition.
Pure-Drive™ circuit design allow 97% of input power to go directly to LEDs.
BUILT TO WITHSTAND THE RELENTLESS PUNISHMENT OF THE DEEP AUSTRALIAN OUTBACK
Finished in 100% Polyester UV and abrasion resistant powder coat, ensures that the bars will never discolour.
Pressure Equalization vent | Protects against water ingress, dust & contaminants.
IP68 | Dust & Particle tight + Water-proof up to 3 meters!
Environmentally sealed Deutsch ® DT-2 connector.
Protected against EMC and RFI.
Ultra-Low 51mm profile without the side brackets & 63mm with side brackets!
Backed by a Stedi 5 Year Replacement Warranty.
- Product details and blurb care of STEDI
WHAT’S IN THE BOX
ST3K 11.5 inch LED LIGHT BAR
Low Profile Stainless Side Brackets
Stainless Fasteners
DT Wire Tail
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
EVOLUTION
To us, evolution means more than just gradual improvement or progression, it is about the whole process; substantial refinement in the pursuit of excellence. After 3 years of design, hundreds of prototypes, and thousands of iterations, with one eye on the future, we have set our sights beyond typical shapes with the creation of TYPE-X™ EVO, redefining auxiliary driving lights as we know them.
THE BEST OF BOTH WORLDS
TYPE-X™ EVO has arrived in a separate dedicated flood and spot beam pattern, meaning you can mix and match, and have full control of your desired beam to suit your driving. Utilising a more efficient technology from CREE’s XP range of LEDs, TYPE-X™ EVO offers up to a staggering 1470m of light throw down the road, and up to a 140m of light spread laterally into the critical zones. Promising an even more intense beam pattern, the TYPE-X™ EVO is the thrilling evolution of the STEDI legacy.
SHAPING THE FUTURE
If you want to know what the future of driving lights looks like, you’re looking at it. This is where finely-honed bespoke craftsmanship and next-generation design meet. Minimalism and purity work in harmony creating curves that complement the future of automotive. TYPE-X™ EVO’s daring attitude and timeless design embodies a vision to tomorrow, pushing the boundaries of what we thought was possible. Taking a step into the future doesn’t mean you can’t write a little history along the way.
WHAT'S INCLUDED
1 x STEDI Type-X™ EVO LED Driving Light Flood Beam
1 x Protective STEDI Black Out Cover
1 x Grey Colour Fascia
1 x Orange Colour Fascia
1 x Type-X™ EVO Bag
Complete Bracket & Stainless Steel Fastener Kit
Fitting Instructions
Wiring Harness (optional)
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
Introducing ScanGauge-3
All The Features You've Been Asking For
ScanGaugeIII can help you monitor your vehicle’s most vital systems and provide the kind of real-time information you’ve been missing. Features include built-in digital gauges, 5 sets of trip data and an easy-to-use Scan Tool that shows both set and pending trouble codes — all in an ultra compact design that installs in minutes.
The new ScanGauge-III features capacitive touch screen with over 16 million possible colours, audible and visual alarms, automatic X-Gauge configuration and configurable gauges display for up to 9 gauges on each screen saved to your preference.
Introducing the NARVA EX2 range of driving lights which has been designed with the DIY 4WD enthusiast in mind and is also ideal for a wide range of fleet and transport applications! With EXceptional beam pattern performance, EXtra-easy installation, EXceptional build quality and EXtensive customisation options to EXpress yourself.
Technical Information
INPUT VOLTAGE RANGE 9 – 33V
CURRENT DRAW @13.5V: 11.6A
LEDs 24 x 5 Watt Cree LEDs
LUMENS 16,320 raw / 12,000 effective
IP RATING IP68 & IP69K
COLOUR TEMPERATURE 5700°K
OTHER Beam type: Hybrid
Narva P/N: 72172
Ensure the safety of your camper or caravan when you're not there with Cruisemaster's own DO35 lock.
Gen.2 DO35 Lock at all new lower price!
The Cruisemaster™ DO35 Lock assembly consists of a dummy pin, two keys and lock chamber with dust cover.
How does it work? The dummy pin is to be inserted into the DO35 universal joint from the top end and the tip of the pin will protrude out at the bottom. The lock is then fitted to the protruding end of the pin and can be locked with a key. The coupling becomes inoperable which prevents others being able to hitch up to your trailer or van when your not there.
This product is covered by a 12 Month Manufacturers Warranty.
Warranty T&C's Apply.
IMPORTANT: Lock is suitable for All Versions of DO35 & DO45 V1 Only
Not suitable for DO45Plus
Usually ships within 2-3 business days
The DO35 Tow Pin Kit is perfect for those with a 2nd tow vehicle or those looking to replace an existing DO35 Pin.
Compatible with older versions of DO35
This kit includes;
Standard DO35 Tow Pin
Pin Cover
C-Spanner
Please note this product has a 7/8" - 22mm shaft, please ensure your tow tongue is the correct size to receive this shaft.
Usually ships within 2-3 business days
BUILT TO SHINE.
The ST3301 Pro Series 4.6" 2 LED Work Light has been designed to offer a high volume of light in the mid-range, with excellent visibility on the road shoulders. By incorporating the superior technology of OSRAM™ LEDs, we have been able to deliver a sophisticated lighting technology within a small but sturdy work light suited for any application.
Being a strong performance beam suited for any application, we thought it would be perfect as a small but sturdy work light. With this size, you will be able to omit a powerful beam in order to illuminate any space, large or small.
SLICKER THAN YOUR AVERAGE WORKLIGHT.
The Pro 4.6” 2 LED Work Light is one of the members of our latest ST3301 range. Re-structured from our popular ST3300, the ST3301 LED range boasts an improved lighting technology with impeccable aesthetics.
Not only have we increased the brightness, but we’ve also optimised the colour temperature to 5500K for a remarkable colour rendition.
With an Ingress Protection rating of IP68 (backed by a certificate of conformity), this is a light that is built to withstand dust ingression and long periods of water immersion.
BRILLIANCE OF THE HIGHEST ORDER.
The all-new flood reflector design minimizes light scatter on the vertical axis, allowing for a more concentrated illumination. This means that there is more light where it matters most. The half-width beam angle of 45° allows for a range of rotations, achieving an excellent light coverage.
KEY TECHNICAL BREAKDOWN
Ingress Protection IP68 (Backed by a certificate of conformity),
Coordinated Colour Temperature 5600K - Excellent colour contrast.
2 Flood Reflector Distribution
Tough GE Lexan primary lens which 250 times the impact-resistant strength of glass and 30 times stronger than acrylic Poly-carbonate.
Waterproof Deutsch DT Connector
Adjustable slide mounts included, with optional side bracket sold separately.
Guaranteed against electromagnetic (EMC) and radio frequency (RFI) interference
TECH SPECS
LUMEN 1,720Lm (RAW)
OPERATING VOLTAGE 10-45V DC
OPERATING TEMPERATURE -40°C - 60°C
WATERPROOF RATE IP 68
LED 2 x OSRAM™
COLOUR TEMPERATURE 5600K
MATERIAL Die-Cast Aluminium
LENS GE Lexan ™
MOUNTING BRACKET Aluminium
BOLTS AND FITTINGS 3 Series Stainless Steel
FLOOD BEAM ANGLE 45°
LUMEN MAINTENANCE 50,000 LM-80
WEIGHT 600g
CURRENT DRAW 1.4A @ 13.6v
WHAT'S INCLUDED
1 x ST3301 PRO 4.6 INCH
2 x Coloured side caps (Grey)
2 x Coloured side caps (Orange)
Stainless Steel Nuts & Bolts
Stainless U Mounting Brackets
Male and Female Deutsch Connectors
Installation Quotes Available by request
Installations are only available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
ADR COMPLIANCE.
With most states in Australia limiting any auxiliary lights to a maximum of 4 forward-facing lights, exceeding this number can render the car to be uncompliant with ADR. When you have exceeded this maximum, covering any exceeding lights with blackout covers whilst driving on public roads will label them as not in use, therefore they are not considered in the overall count.
USA / EURO.
This can apply overseas in most parts of the US, Europe, South Africa, and more requiring any auxiliary driving light to be covered when on public roads.
THE PRO STANDARD.
Suited to our STEDI Type-X Pro 8.5 Inch LED Driving Lights and Type-X Sport 8.5 Inch LED Driving Lights. Whether you are chasing down a STENCIL print or just wanting to put on a cheeky SMILEY cover, then look no further!
STEDI P/N: CVRTYPE-X-SMILE
COMPACT DESIGN. MEGA PERFORMANCE.
The compact-LED driving light space has been fearfully neglected, with offerings looking as underwhelming as their inability to sustain a compact performance. Enter the all-new STEDI QUAD Pro.
A LEGENDARY BLOODLINE.
The QUAD Pro is the continuation of the high-calibre class of the PRO bloodline. Sharing the legendary performance of the Type-X Pro and ST3303 Pro, the QUAD Pro utilises the same reflector and LED technology, to deliver an explosive performance.
CUSTOMISABLE LIKE NO OTHER
Included in the kit is a pair of STEDI blackout cover, in addition to the orange and grey colour customisation caps. The iconic STEDI Smiley covers are available to purchase separately, as are blue, green, red, and yellow colour caps.
RAZOR-SHARP LUMINANCE.
Our Quads showcase a glistening 5700K colour temperature, providing the necessary luminance to cut-through any obstrusive dust and other air-born particles.
TAKE YOUR PICK.
The compact housing design offers endless possibilities in terms of mounting locations. We think these are going to be hugely popular as roof-mounted arrays and on bull bars with minimal clearance like the AFN bars.
ScanGauge products are designed to plug directly into the vehicle diagnostic connector located under the dash. ScanGauge effectively monitors and provides heaps of real-time information crucial to manage your vehicle. Incorporates well over 15 digital gauges, trip data consisting of 5 sets as well as an Engine Scan Tool whose main function is to bring alert to you of any set and pending trouble codes.
ScanGauge-II and ScanGauge-E are suitable for all petrol and diesel OBDII compatible vehicles with 16-PIN connector. ScanGauge-KR and ScanGauge-D are suitable for all large diesel vehicles with 9-PIN J1939 and 6-PIN J1708 connectors.
ScanGaugeII features include our exclusive X-Gauge technology, which lets you program new gauges and a built-in Performance Monitor.
Compatible with all OBDII protocols
More than 15 Built-in Digital Gauges
Check & Clear Trouble Codes
Multiple Trip Computers
X-Gauge programmable gauge system
Performance Monitor
Introducing the NARVA EX2 range of driving lights which has been designed with the DIY 4WD enthusiast in mind and is also ideal for a wide range of fleet and transport applications! With EXceptional beam pattern performance, EXtra-easy installation, EXceptional build quality and EXtensive customisation options to EXpress yourself.
Technical Information
INPUT VOLTAGE RANGE 9 – 33V
CURRENT DRAW @13.5V: 9.5A
LEDs 24 x 5 Watt Cree LEDs
LUMENS 12,000 raw / 9,200 effective
IP RATING IP68 & IP69K
COLOUR TEMPERATURE 5700°K
OTHER Beam type: Hybrid
Narva P/N: 72162
ITEM INCLUDES
DO45 Plus (With Handbrake)
Tow Pin 1 1/4" Shaft
Tow Pin Cover
Universal C-Spanner
Fitment Bolts
User Guide
Tame the Beast with the DO45 Plus!
PLUS SERIES EXCLUSIVE FEATURES
Patented “Checklock” Gen.2 Dust Cap & Bumper for an easy, secure seal
Improved Bumper now includes reflective reversing strip for easy alignment
Rear support webbing allows for mounting upside down on the underside of the drawbar
FEATURES
D-Value & V-Value ADR Compliant
2 Stage ADR compliant locking mechanism
Low profile Bumper & Cap for impressive clearance
High articulation for improved handling off-road and on unmaintained roads
Available with or without handbrake
Suitable for use with Weight Distribution System’s (where applicable)
Forged Yoke and Rear Nut for added strength
One piece light weight Cast Housing
Improved towing safety
Combination of zn-ni and e-coat for superior corrosion protection
Greaseable Bushes for easy maintenance and noise free towing
No tow ball height restrictions
R.A.T Run Tested and Proven
ARTICULATION: 360 degrees axial, minimum 70 degrees other axes.
LOCKING: Fully ADR 62/02 compliant including automatic secondary lock
BOLT PATTERN: 4 bolts at 185mm x 76mm (Front) x 54mm (Rear)
RATING: 4.5 Tonne
ACTION: Drop-On
MAINTENANCE: Fully Greasable
For instructions on installation, maintenance and use refer the DO45Plus User Guide.
*Please note while the DO45Plus’s Zn-Ni with E-Coat provides superior corrosion protection it may fade with extended exposure to UV. This does not affect the operation of the DO45Plus. To best maintain the finish of the product, we recommend covering the DO45Plus coupling when not in use if stored outside and exposed to direct UV.
DO45 Version 1 & DO45Plus accessories and fittings are not interchangable
FREE SHIPPING AUS WIDE
* Please note product supplied and product shown may have minor cosmetic discrepancies
Usually ships within 2-3 business days
Get a spare DO45Plus Tow Pin for your second vehicle.
Forged steel tow pin rated to tow 4.5T off-road.
The DO45Plus tow pin is only compatible with our Cruisemaster DO45Plus coupling.
This kit includes;
Standard DO45Plus Tow Pin
Pin Cover
C-Spanner
Please note this product has a 1 1/4" or 32mm shaft, please ensure your tow tongue is the correct size to receive this shaft.
IMPORTANT: Pin is suitable for use with DO45Plus Only, NOT for use with DO45 V1
Usually ships within 2-3 business days
STEDI DESIGN LANGUAGE.
Some people call it the little things. For us, it is literally everything. We obsessed over even the most trivial geometries and design elements to achieve a visually stunning luminaire. The 4mm 304 Stainless steel bracket features our signature shoulder armour with laser-cut STEDI™ branding. A carefully considered orange rim surrounding the housing offers just the right amount of visual impact while ensuring that the overall look and feel play nicely equally on a Sandy Taupe Landcruiser as it will on Magnetic Grey Ranger.
LEGENDARY TYPE-X DNA.
It's been a few years since the inception of the original Type-X™. We’ve taken an already proven platform and completely redesigned it from the ground up. The 7" Type-X™ Sport features an increased optics depth of 35%, allowing for a perfectly collimated beam and the resultant increase in light intensity. The beam diameter strikes a sublime balance between width and throw, sending light right out to 895m. Four dedicated built-in wide-beam optics disperse light in the nearfield, and transition beautifully with the spot beam.
HIGH PERFORMANCE - ACCESSIBLE PRICE.
The 7" Type-X™ Sport; our most affordable driving light yet, with the inherented STEDI™ ability to deliver a high-performance and high-quality driving illuminance. Simply look at the build quality and performance of other offerings on the market and you will be convinced that the 7" Type-X™ Sport remains untouched.
EVOLUTION
To us, evolution means more than just gradual improvement or progression, it is about the whole process; substantial refinement in the pursuit of excellence. After 3 years of design, hundreds of prototypes, and thousands of iterations, with one eye on the future, we have set our sights beyond typical shapes with the creation of TYPE-X™ EVO, redefining auxiliary driving lights as we know them.
THE BEST OF BOTH WORLDS
TYPE-X™ EVO has arrived in a separate dedicated flood and spot beam pattern, meaning you can mix and match, and have full control of your desired beam to suit your driving. Utilising a more efficient technology from CREE’s XP range of LEDs, TYPE-X™ EVO offers up to a staggering 1470m of light throw down the road, and up to a 140m of light spread laterally into the critical zones. Promising an even more intense beam pattern, the TYPE-X™ EVO is the thrilling evolution of the STEDI legacy.
SHAPING THE FUTURE
If you want to know what the future of driving lights looks like, you’re looking at it. This is where finely-honed bespoke craftsmanship and next-generation design meet. Minimalism and purity work in harmony creating curves that complement the future of automotive. TYPE-X™ EVO’s daring attitude and timeless design embodies a vision to tomorrow, pushing the boundaries of what we thought was possible. Taking a step into the future doesn’t mean you can’t write a little history along the way.
WHAT'S INCLUDED
1 x STEDI Type-X™ EVO LED Driving Light Flood or Spot Beam (user defined)
1 x Protective STEDI Black Out Cover
1 x Grey Colour Fascia
1 x Orange Colour Fascia
1 x Type-X™ EVO Bag
Complete Bracket & Stainless Steel Fastener Kit
Fitting Instructions
Wiring Harness (optional)
Installation is available from the Cruisemaster Towing Performance Centre (352 Bilsen Road, GEEBUNG 4034). Installs available via booking Mon - Thurs 7.30am - 4.30pm Fri 7.30am - 12.30pm.
Additional charges apply
Introducing the NARVA EX2 range of driving lights and light bars which has been designed with the DIY 4WD enthusiast in mind and is also ideal for a wide range of fleet and transport applications! With EXceptional beam pattern performance, EXtra-easy installation, EXceptional build quality and EXtensive customisation options to EXpress yourself.
Technical Information
INPUT VOLTAGE RANGE 9-33V DC
CURRENT DRAW @13.5V/@28V: 7.2/3.5
LEDs 36
LUMENS Effective: 9780Lm
IP RATING IP68 & IP69K
OPERATING TEMPERATURE -40 - +60°
COLOUR TEMPERATURE 5700K ±5%
ECE R10
OTHER Raw lumens: 6120Lm
Narva P/N: 72842